FAQs

What gauges would you suggest for a 1994-1997 12v Diesel Dodge Ram?

The most commonly selected gauges for this type of vehicle are 35 PSI Boost Gauge, 1500 Exhaust Temperature Gauge, Transmission Temperature Gauge and or 30 PSI Fuel Pressure Gauge.

What accessories are needed to install a fuel pressure gauge on a 1994-1997 Dodge Ram Diesel?

For the 1994-1997 Dodge Ram 12v 5.9L Cummins with a P7100 pump, the Banjo Bolt/Snubber Combo Adapter would allow you to easily install your Snubber Valve and fuel pressure sensor directly to the fuel filter housing. This combo fitting also...

Do I need a Test port Extender on a 1997-1997 Dodge with the 47RE Transmission and why?

Yes, a ⅛-27 NPT test port extender is required when installing our sensor into a 47RE transmission. The reason for the extender is due to the test port location on the transmission is too shallow and could cause the internals of the transmissions...

Can my fuel pressure sensor be installed directly to my aftermarket lift pump on my 1994-1997 Dodge Ram?

With most aftermarket lift pumps such as (Fass or AirDog), there are pressure ports on the pumps directly. As long as those ports are a ⅛-27 NPT thread, our sensor can be installed. Keep in mind, even with an aftermarket lift pump installed, a...

Why is a Snubber Valve needed on a 1994-1997 (12 Valve) Dodge Diesel?

GlowShift's 1/8-27 NPT Fuel Pressure Snubber Valve regulates, normalizes and eliminates fuel pressure spikes present throughout the fuel system during the initial ignition and start-up of a Cummins diesel engine. The Snubber Valve limits and...

Will the 1994-1997 Dodge Ram Pod work with Gasoline 1500/2500 Trucks?

Yes, our pod will work with the 1994-1997 Gasoline 5.2L/5.9L Magnum V8 Trucks. The cab body of the trucks between Gasoline and Diesel did not change.

Can I install my transmission temperature sensor in a Manual Transmission on a 1994-1997 Dodge Ram?

Unfortunately, Manual transmission are sealed units and do not have “Test ports” like an automatic transmission. Manual transmission only holds enough fluid to cover all the synchro since in movement. Due to this, a sensor cannot be installed in...

How come there is not a Boost Bolt for the 12v Cummins Engine but there is a Boost Bolt for the 24v Cummins 5.9/6.7 Engine?

The reason there is not a boost bolt for the 12v Cummins engine applications is that on the driver side of the cylinder head of the 12v, there is a boost port thread size of ⅛-27 NPT already there from the factory. The 24v 5.9/6.7 Cummins...

Does the 1994-1997 Dodge Ram Pod come in any other colors than Black?

At this time currently, the 1994-1997 Dodge Ram Dual/Triple pillar pods only come in Black. Glowshift pods are made from high-quality ABS plastic and can be painted with any plastic bonding paint.

Is the 1994-1997 Dodge Ram pod a complete replacement or layover pod?

The 1994-1997 Dodge Ram Pod is a layover style pillar. Here is a link to our installation instructions. For installation, this will require you to fully remove your factory A-pillar trim molding. Once the factory trim is completely removed from...

What are some suggestions to avoid pinching or kinking the boost hose?

When working with the boost line we suggest being very gentle with it and loosely run it to the location you are installing it in. From there you can gently tuck away the line being careful not to take any sharp bends.

What would happen if I don’t use the snubber valve?

With any Dodge diesel vehicles there is pressure spike when you first start the vehicle. If you do not have a snubber valve installed the pressure spike will cause the sensor fail.

How do I ensure that there is a good connection on the bullet style connectors for my sensor harness?

When using the bullet style connectors you should be able to feel the connectors “click” when they are seated properly.