This pod is a complete replacement for the factory A-Pillar. You will need to remove your stock A-pillar to install this Triple Pillar Pod. To remove the Factory A-Pillar you will need to pull and release the spring clip which is located 4 ¼” down...
You would have to turn the pod toward the windshield for it to sit correctly. Install the clip and tighten the screw which will secure the pod in place.
Unfortunately, we do not offer a four gauge pillar pod for this vehicle.
Yes, our pod will work with the Gasoline 1998-2002 Trucks. The cab body of the trucks between Gasoline and Diesel did not change.
Yes, our pod will still work with your application. The first half of 1998 the Dodge Ram’s came with a new body style but with the 12 Valve Cummins Engine.
If you have an aftermarket intake with an existing ⅛-27 NPT port, we would suggest using this port for your installation method.
Both drilling and or installing the boost bolt adapter will give you 100% accurate readings. Unfortunately, there is no “Best” option as they are both great options. However, drilling and tapping the manifold can be a very intensive job and is why...
Yes, the 6.7L Boost Bolt is compatible with both the 6.7L, as well as the 5.9L.
Yes, a ⅛-27 NPT test port extender is required when installing our sensor into a 47/48RE transmission. The reason for the extender is due to the test port location on the transmission is too shallow and could cause the internals of the...
Unfortunately, Manual transmission are sealed units and do not have “Test ports” like an automatic transmission. Manual transmission only holds enough fluid to cover all the synchro since in movement. Due to this, a sensor cannot be installed in...
Yes, when installing a sensor into your vehicle’s test port a test port extender is required to install our temperature sensor to keep the sensor clear from coming into contact with the internals of your vehicle’s transmission.
If a Test Port Extender is not used the transmission temp sensor will come in contact with the internals of the transmission. This could possibly cause major damage to your transmission as well as damage the sensor. We suggest using the Test Port...
Most aftermarket lift pumps offer a test port that will allow the snubber valve and sensor to be screwed into. We would suggest confirming this with your specific pump.
GlowShift’s 1998.5-2007 Dodge Ram 5.9L Cummins 3/8” Big Line Kit upgrades the restrictive line and enables you to easily install a fuel pressure sensor for extremely accurate readings directly from the source. This 5.9L Cummins Big Line Kit...
GlowShift's 1/8-27 NPT Fuel Pressure Snubber Valve regulates, normalizes and eliminates fuel pressure spikes present throughout the fuel system during the initial ignition and start-up of a Cummins diesel engine. The Snubber Valve limits and...
With most aftermarket lift pumps such as (Fass or AirDog), there are pressure ports on the pumps directly. As long as those ports are a ⅛-27 NPT thread, our sensor can be installed. Keep in mind, even with an aftermarket lift pump installed a...
Yes, you can also install our fuel pressure with our big line kit too. Here is the link to the part on our site. http://www.glowshiftdirect.com/1998-5-2007-dodge-ram-5-9l-cummins-fuel-pressure-big-line-kit/
A Big line is not needed. However, we designed the big line kit to generate a secondary way to install a fuel pressure gauge to your vehicle while increasing the volume of fuel.
For the 1998.5-2002 Dodge Ram 24v 5.9L Cummins, the Banjo Bolt/Snubber Combo Adapter would allow you to easily install your Snubber Valve and fuel pressure sensor directly to the fuel filter housing. This combo fitting also includes 2 crush...
The most commonly selected gauges for this type of vehicle are Oil Pressure, Voltage, or Transmission Temperature Gauges.
The most commonly selected gauges for this type of vehicle are 60 PSI Boost Gauge, 1500 Exhaust Temperature Gauge, Transmission Temperature Gauge and or 30 PSI Fuel Pressure Gauge.
Our 3/4unf-16 thread oil filter adapter will work with the Gasoline 5.2L / 5.9L engines. Our 1”-16 thread oil filter adapter will work with Diesel 5.9L / 6.7L engines.
The Dode Ram 24V Cummins has a ⅛-27 NPT port on the top of the oil filter assembly. This port will fit our oil temperature and oil pressure sensors with no additional adapters required.
Unfortunately, at this time we do not offer an install guide for a Gasoline 5.2L / 5.9L 1998-2002 Dodge Ram.